WDT — Watchdog timer

A countdown watchdog timer using the low-frequency clock source (LFCLK) offers configurable and robust protection against application lock-up.

The watchdog timer is started by triggering the START task.

The watchdog can be paused during long CPU sleep periods for low power applications and when the debugger has halted the CPU. The watchdog is implemented as a down-counter that generates a TIMEOUT event when it wraps over after counting down to 0. When the watchdog timer is started through the START task, the watchdog counter is loaded with the value specified in the CRV register. This counter is also reloaded with the value specified in the CRV register when a reload request is granted.

The watchdog’s timeout period is given by:

      timeout [s] = ( CRV + 1 ) / 32768

When started, the watchdog will automatically force the 32.768 kHz RC oscillator on as long as no other 32.768 kHz clock source is running and generating the 32.768 kHz system clock, see chapter CLOCK — Clock control.

Reload criteria

The watchdog has eight separate reload request registers, which shall be used to request the watchdog to reload its counter with the value specified in the CRV register. To reload the watchdog counter, the special value 0x6E524635 needs to be written to all enabled reload registers.

One or more RR registers can be individually enabled through the RREN register.

Temporarily pausing the watchdog

By default, the watchdog will be active counting down the down-counter while the CPU is sleeping and when it is halted by the debugger. It is however possible to configure the watchdog to automatically pause while the CPU is sleeping as well as when it is halted by the debugger.

Watchdog reset

A TIMEOUT event will automatically lead to a watchdog reset.

See Reset for more information about reset sources. If the watchdog is configured to generate an interrupt on the TIMEOUT event, the watchdog reset will be postponed with two 32.768 kHz clock cycles after the TIMEOUT event has been generated. Once the TIMEOUT event has been generated, the impending watchdog reset will always be effectuated.

The watchdog must be configured before it is started. After it is started, the watchdog’s configuration registers, which comprise registers CRV, RREN, and CONFIG, will be blocked for further configuration.

The watchdog can be reset from several reset sources, see Reset behavior.

When the device starts running again, after a reset, or waking up from OFF mode, the watchdog configuration registers will be available for configuration again.

Registers

Table 1. Instances
Base address	Peripheral	Instance	Description	Configuration
0x40010000	WDT	WDT	Watchdog timer

Table 2. Register Overview
Register	Offset	Description
TASKS_START	0x000	Start the watchdog
EVENTS_TIMEOUT	0x100	Watchdog timeout
INTENSET	0x304	Enable interrupt
INTENCLR	0x308	Disable interrupt
RUNSTATUS	0x400	Run status
REQSTATUS	0x404	Request status
CRV	0x504	Counter reload value
RREN	0x508	Enable register for reload request registers
CONFIG	0x50C	Configuration register
RR[0]	0x600	Reload request 0
RR[1]	0x604	Reload request 1
RR[2]	0x608	Reload request 2
RR[3]	0x60C	Reload request 3
RR[4]	0x610	Reload request 4
RR[5]	0x614	Reload request 5
RR[6]	0x618	Reload request 6
RR[7]	0x61C	Reload request 7

INTENSET

Address offset: 0x304

Enable interrupt

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	RW	TIMEOUT										Write '1' to Enable interrupt for TIMEOUT event See EVENTS_TIMEOUT
			Set	1								Enable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled

INTENCLR

Address offset: 0x308

Disable interrupt

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	RW	TIMEOUT										Write '1' to Disable interrupt for TIMEOUT event See EVENTS_TIMEOUT
			Clear	1								Disable
			Disabled	0								Read: Disabled
			Enabled	1								Read: Enabled

RUNSTATUS

Address offset: 0x400

Run status

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id																																			A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	R	RUNSTATUS										Indicates whether or not the watchdog is running
			NotRunning	0								Watchdog not running
			Running	1								Watchdog is running

REQSTATUS

Address offset: 0x404

Request status

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id																												H	G	F	E	D	C	B	A
Reset 0x00000001				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	1
Id	RW	Field	Value Id	Value								Description
A	R	RR0										Request status for RR[0] register
			DisabledOrRequested	0								RR[0] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[0] register is enabled, and are not yet requesting reload
B	R	RR1										Request status for RR[1] register
			DisabledOrRequested	0								RR[1] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[1] register is enabled, and are not yet requesting reload
C	R	RR2										Request status for RR[2] register
			DisabledOrRequested	0								RR[2] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[2] register is enabled, and are not yet requesting reload
D	R	RR3										Request status for RR[3] register
			DisabledOrRequested	0								RR[3] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[3] register is enabled, and are not yet requesting reload
E	R	RR4										Request status for RR[4] register
			DisabledOrRequested	0								RR[4] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[4] register is enabled, and are not yet requesting reload
F	R	RR5										Request status for RR[5] register
			DisabledOrRequested	0								RR[5] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[5] register is enabled, and are not yet requesting reload
G	R	RR6										Request status for RR[6] register
			DisabledOrRequested	0								RR[6] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[6] register is enabled, and are not yet requesting reload
H	R	RR7										Request status for RR[7] register
			DisabledOrRequested	0								RR[7] register is not enabled, or are already requesting reload
			EnabledAndUnrequested	1								RR[7] register is enabled, and are not yet requesting reload

CRV

Address offset: 0x504

Counter reload value

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0xFFFFFFFF				1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1
Id	RW	Field	Value Id	Value								Description
A	RW	CRV		[0x0000000F..0xFFFFFFFF]								Counter reload value in number of cycles of the 32.768 kHz clock

RREN

Address offset: 0x508

Enable register for reload request registers

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id																												H	G	F	E	D	C	B	A
Reset 0x00000001				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	1
Id	RW	Field	Value Id	Value								Description
A	RW	RR0										Enable or disable RR[0] register
			Disabled	0								Disable RR[0] register
			Enabled	1								Enable RR[0] register
B	RW	RR1										Enable or disable RR[1] register
			Disabled	0								Disable RR[1] register
			Enabled	1								Enable RR[1] register
C	RW	RR2										Enable or disable RR[2] register
			Disabled	0								Disable RR[2] register
			Enabled	1								Enable RR[2] register
D	RW	RR3										Enable or disable RR[3] register
			Disabled	0								Disable RR[3] register
			Enabled	1								Enable RR[3] register
E	RW	RR4										Enable or disable RR[4] register
			Disabled	0								Disable RR[4] register
			Enabled	1								Enable RR[4] register
F	RW	RR5										Enable or disable RR[5] register
			Disabled	0								Disable RR[5] register
			Enabled	1								Enable RR[5] register
G	RW	RR6										Enable or disable RR[6] register
			Disabled	0								Disable RR[6] register
			Enabled	1								Enable RR[6] register
H	RW	RR7										Enable or disable RR[7] register
			Disabled	0								Disable RR[7] register
			Enabled	1								Enable RR[7] register

CONFIG

Address offset: 0x50C

Configuration register

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id																																C			A
Reset 0x00000001				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	1
Id	RW	Field	Value Id	Value								Description
A	RW	SLEEP										Configure the watchdog to either be paused, or kept running, while the CPU is sleeping
			Pause	0								Pause watchdog while the CPU is sleeping
			Run	1								Keep the watchdog running while the CPU is sleeping
C	RW	HALT										Configure the watchdog to either be paused, or kept running, while the CPU is halted by the debugger
			Pause	0								Pause watchdog while the CPU is halted by the debugger
			Run	1								Keep the watchdog running while the CPU is halted by the debugger

RR[0]

Address offset: 0x600

Reload request 0

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

RR[1]

Address offset: 0x604

Reload request 1

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

RR[2]

Address offset: 0x608

Reload request 2

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

RR[3]

Address offset: 0x60C

Reload request 3

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

RR[4]

Address offset: 0x610

Reload request 4

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

RR[5]

Address offset: 0x614

Reload request 5

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

RR[6]

Address offset: 0x618

Reload request 6

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

RR[7]

Address offset: 0x61C

Reload request 7

Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Id				A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A	A
Reset 0x00000000				0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0
Id	RW	Field	Value Id	Value								Description
A	W	RR										Reload request register
			Reload	0x6E524635								Value to request a reload of the watchdog timer

Electrical specification

Watchdog Timer Electrical Specification

Symbol	Description				Min.	Typ.	Max.	Units
I_WDT	Run current for watchdog timer					0.3	2	µA
t_WDT	Time out interval				458 µs		36 h