MEMCONF — Memory configuration

MEMCONF provides power control for RAM blocks.

Each RAM block can independently power up or power down in System ON and System OFF mode. RAM blocks can contain multiple RAM sections. For more information about System ON and System OFF modes, see Power and clock management. For an overview of available RAM blocks and RAM sections, see Memory.

MEMCONF registers are used for configuring the following:

RAM sections to be retained during System OFF mode
RAM sections to be retained and accessible during System ON mode

In System OFF mode, a RAM section is retained by configuring the corresponding MEM[i] field of the RET register.

In System ON mode, retention and accessibility for a RAM section is configured in the corresponding MEM[i] field of register POWER[n].CONTROL (n=0..1).

A complete list of blocks (RET.MEM[i], RET2.MEM[i], and CONTROL.MEM[i]) are found in the following table.

Table 1. Memory block overview with MEMCONF.POWER configuration
Block number (index i in MEMCONF.POWER)	RAM section	RET reset value	CONTROL reset value
0	RAM00 section 0	1	1
1	RAM01 section 0	1	1
2	RAM01 section 1	1	1
33	ICACHE tag + data 1:0	1	1

The following table summarizes the behavior of the CONTROL and RET fields when a power domain is powered on or off. The RAM section can be used to read and write data when it is powered. The RAM section is retained during System OFF.

Table 2. RAM section configuration
Configuration			RAM section status
Power mode	CONTROL	RET	Powered	Retained
System OFF	Any value	Off	No	No
System OFF	Off	On	No	No
System OFF	On	On	No	Yes
System ON IDLE	Off	Any value	No	No
System ON IDLE	On	Any value	No	Yes
System ON RUN	Any value	Any value	Yes	Yes

The advantage of not retaining RAM content is reduced overall current consumption.

See chapter Memory for more information on RAM sections.

Note: CACHE — Instruction/data cache must be disabled when the ICACHE memory block is turned off, and only enabled after the ICACHE memory block is turned on.

Registers

Instances


Instance	Domain	Base address	Description
MEMCONF	GLOBAL	0x400CF000	Memory Configuration MEMCONF

Configuration


Instance	Domain	Configuration
MEMCONF	GLOBAL

Register overview


Register	Offset	Description
POWER[n].CONTROL	0x500	Control memory block power.
POWER[n].RET	0x508	RAM retention for RAM [n].

POWER[n].CONTROL

Address offset: 0x500 + (n × 0x10)

Control memory block power.

Where n = 0 for memory blocks 0 to 31 and n = 1 for memory blocks 32 to 63.


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				f	e	d	c	b	a	Z	Y	X	W	V	U	T	S	R	Q	P	O	N	M	L	K	J	I	H	G	F	E	D	C	B	A
Reset 0xFFFFFFFF				1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1
ID	R/W	Field	Value ID	Value								Description
A-f	RW	MEM[i] (i=0..31)										Keep the memory block MEM[i] on or off when in System ON mode. RAM blocks powered off this way will not be retained. All RAM blocks will be off in System OFF mode.
			Off	0								Power down
			On	1								Power up

POWER[n].RET

Address offset: 0x508 + (n × 0x10)

RAM retention for RAM [n].

Where n = 0 for RAM blocks 0 to 31 and n = 1 for RAM blocks 32 to 63.


Bit number				31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ID				f	e	d	c	b	a	Z	Y	X	W	V	U	T	S	R	Q	P	O	N	M	L	K	J	I	H	G	F	E	D	C	B	A
Reset 0xFFFFFFFF				1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1	1
ID	R/W	Field	Value ID	Value								Description
A-f	RW	MEM[i] (i=0..31)										Keep the RAM block MEM[i] retained when in System OFF mode. All other RAM will be off in System OFF mode.
			Off	0								Retention off
			On	1								Retention on